WeepEase™: The Missing Step for Clean, Compliant Weep Holes

Bricklayers have been using Weepa's for years. But there's always been a step missing.
Right now there's a lot of talk across the industry about weep hole compliance. Inspectors are checking them, and homeowners are noticing them. That's exactly why DAT Tools made WeepEase™.
What the building code says
Under the NCC Housing Provisions, Part 5.7.5, weep holes (open perpend joints) go in the course immediately above any flashing, including a damp-proof course acting as a flashing. Each one must be at least 50 mm high by the width of the perp, at no more than 1.2 m centres. There are some exceptions, so always check the plans, your state's requirements and the guidance from Think Brick Australia.
NCC 2025 raises the bar again. In climate zones 6, 7 and 8, the cavity behind brick veneer and cavity brick now has to be ventilated as well as drained, with at least 1,000 mm² of opening per metre of wall at the base and the top. On a standard brick, that works out to a weep hole at around every fourth perp. It already applies in Victoria, the ACT and WA, with Queensland and South Australia following from 1 May 2027. NSW and Tasmania have their own variations to this part of the code, so check locally. Our guide to weep hole requirements in Australia breaks it down state by state.
A weep hole only works if it's open. Mortar left in the hole, or dropped onto the flashing behind it, can stop water draining out of the cavity. Weepa explains why weep holes matter in more detail.
Designed by a bricklayer who knows the job
WeepEase™ was developed by Damian Amuso, a bricklayer with more than 27 years on the tools. Damian knows how hard the job is, and if there's a way to make a brickie's life easier, he'll find it. Running several crews at DA Bricklaying, he saw a gap in the market for a tool that forms a clean, compliant weep hole the same way every time. So he designed one, and DAT Tools patented it.
Weepa's and WeepEase™ work together
Weepa's aren't going anywhere, but not every weep hole needs one. It depends on where the build is, its rating and what the plans or engineer specify. Some weep holes are left open. Others are finished with a product like the Weepa range or Weepguard weep hole vents, which keep vermin out while still letting air and water through. WeepEase™ isn't a replacement for any of them. It's the step that comes first, whatever finish the hole ends up with.
Form it. WeepEase™ goes in as you lay and forms the weep hole to size.
Clean it. Pull it out when the mortar is almost dry, and the hole is open and clean. No raking, no chipping out set mortar.
Check it. The inspector can see a clean, open, compliant hole.
Finish it. If the plans call for a Weepa or vent, it slides straight into a properly formed hole, with no forcing it in and no trouble getting it back out if the inspector needs to look. If not, the hole stays open and clean.

Cleaning, compliance and consistency
Cleaning: the hole is formed clean, so there's no going back to rake out mortar after it's gone off.
Compliance: sized for the Australian standard brick, giving an open perp the full height of the brick.
Consistency: every weep hole looks the same, course after course, whoever is on the wall.
Building your own home?
Ask your bricklayer about WeepEase™. Weep holes run right around the bottom of the house and above the flashings over windows and doors. Once the brickwork is done, it's done, and there's nothing worse than a run of uneven, messy weep holes on a brand-new home.
How to use WeepEase™
Clear the mortar so the tool sits on the DPC or flashing, DAT logo up, handle out.
Keep laying as normal. The tool stays in place.
Wait until the mortar is almost dry. Pulling it while the mortar is wet can disturb the work.
Shimmy it up and down and pull it straight out.
Rinse it off and reuse it on the next wall.
Watch the WeepEase™ how-to video on YouTube, and see it on site on Instagram, Facebook and TikTok.
WeepEase™ FAQs
Does WeepEase™ replace Weepa's? No. It forms and cleans the hole. Whether that hole is left open or finished with a Weepa or vent depends on the build and the plans, and if one is specified, it fits properly.
What size brick is it for? It's sized for the Australian standard brick (230 x 110 x 76 mm).
Is it reusable? Yes. It's injection moulded in a tough plastic, with 10 tools in every box.
When do I pull it out? When the mortar is almost dry, not while it's wet.
Who is it for? Bricklayers, builders, site supervisors, building inspectors, and anyone building a new brick home.
Get WeepEase™
Every Australian order from the DAT Tools online store comes with a free WeepEase™ sample.
Tools for brickies, by brickies.





Comments