top of page
Search

Brick Jointers Explained: Which One Suits the Job?

2 hours ago
4 min read
DAT Tools roll jointers in 550 mm and 700 mm, 10 mm and 12 mm

A great wall can be let down by a bad joint. The jointer, and when it's used, makes all the difference to the finish. There are a lot of jointers on the market and every brickie has a favourite. Here's a rundown of the main ones, including the ones the DA Bricklaying crews use every day.

DAT Roll Jointers: why a 700 mm?

DAT Tools roll jointers come in 550 mm and 700 mm. The 700 mm is longer than what you'll usually find, and that's on purpose. Damian Amuso, who develops every DAT Tools product, made it to make jointing faster on long runs. On a long wall, that extra length makes the job just that little bit easier.

Timing is everything

Before picking a jointer, get the timing right. The brickwork needs to be ready to joint, but the mortar can't be too dry. Once the mortar is too dry, a metal jointer won't work properly. It burns the mortar and the bricks and leaves those dark burn marks every brickie knows. That goes for just about any metal jointer.

What a good joint looks like

At a recent Think Brick Australia session for the industry, the message on jointing was simple. A joint is there to give the wall a clean finish, to compact and seal the mortar, and to keep water out. When you step back and look at a finished wall, check for:

  • Joints pulled straight along the course

  • A consistent, shallow depth from one end of the wall to the other

  • A smooth finish on the mortar

That is where a long roll jointer earns its place. A 700 mm DAT Roll Jointer spans more of the course in one pass, which makes it easier to keep the joint straight and the depth even on a long wall.

The five common joint finishes

Think Brick groups the joints you will see on Australian brickwork into five types:

  • Shallow ironed

  • Deep ironed

  • Flush

  • Weather struck

  • Raked

Ironed joints are the everyday finish and the one a roll jointer is made for. Raked joints show off the edges of each brick, but PGH Bricks notes they suit rolled bricks and are not for bricks with a matte or glazed finish. Always check the plans and the brick supplier before choosing a finish.

Why mortar colour changes across a wall

Think Brick also listed what can change the colour of mortar once it is on the wall. Watch out for:

  • Saturated sand

  • Saturated bricks or blocks

  • The wrong ratio of sand to cement

  • Jointing too early or too late

  • Inconsistent tooling of the joint

  • Work left unprotected in bad weather

  • Freeze and thaw cycles in cold areas

Two of those come straight back to the jointer: timing and consistency. Jointing at the same point in the set, with the same tool, keeps the colour even across the wall. Think Brick's Mortar Colour Variation and Pointing fact sheets go into more detail.

The main types of jointer

Jointer

What it is

Best for

Example

Roll jointer

A long jointer run along the bed joint

Straight, even joints, fast on long runs

Barrel jointer

A handle with interchangeable barrels in different sizes

Brickies who like to switch joint sizes

Poly jointer

A plastic jointer

Avoiding the black and burn marks steel can leave

Spoon jointer

A short, spoon-shaped jointer

Perps and tight spots

Dutch jointer

A slim, flat steel jointer

Detail work around the wall


Technique Tools also has a handy rundown of popular bricklayer jointers, and its full jointer range includes poly spoon jointers.

10 mm or 12 mm?

Some brickies like a 10 mm jointer and some like a 12 mm. There's no right answer, it comes down to preference, so DAT Tools makes its roll jointers in both sizes.

DAT Barrel Jointer Set

The DAT Barrel Jointer Set has four interchangeable barrels (13, 16, 19 and 22 mm) on a cast aluminium handle with extra knuckle room. Pick the size and swap it in. It's used every day by the DA Bricklaying crews, and it went home with every competitor at the 2025 Spec Mix Bricklayer 500.

DAT Tools Barrel Jointer Set with four interchangeable barrels and pouch

Technique Tools poly jointer

The Technique Tools poly jointer is another favourite, and the DA Bricklaying crews use it too. It has 10 mm and 12 mm edges and a pointed end for getting into corners. Being plastic, it avoids the black marks steel jointers can leave, which makes it great on light-coloured mortar. It comes in 300 mm and 550 mm.

Get the set

Good joints start with a clean wall, and so do good weep holes. WeepEase™ forms clean, consistent, compliant weep holes as you lay, in line with the NCC weep hole requirements.

Every Australian order from the DAT Tools online store comes with a free WeepEase™ sample.

Tools for brickies, by brickies.

Comments


bottom of page